4 Inch Marine Pump Description
When extreme marine conditions demand relentless dredging power, the Hydroman 100THY Hydraulic Pump for Marine Dredging proves indispensable. Specifically, the 100THY37-6P Excavator Hydraulic Pump for Sea Work delivers unmatched reliability. This 4 Inch Hydraulic Submersible Pump for Marine Slurry handles sand, gravel, and sediment with ease. As a Vertical Hydraulic Pump for Offshore Underwater Operation, it mounts directly onto excavators for deep-sea tasks. Additionally, this 37kW Hydraulic Dredge Pump for Sea Applications ensures high flow rates under heavy loads. Built for abrasive environments, it resists wear far longer than conventional pumps. Whether you’re deepening shipping channels or mining underwater aggregates, this pump keeps working where others fail.
Design Features of the 100THY37-6P Excavator Hydraulic Pump for Sea Work
Engineered from the seabed up, this pump incorporates five critical design elements that extend service life and boost productivity.
Hardened Chrome-Iron Impeller and Casing – The hydraulic path uses high-chrome cast iron with a hardness of 58-62 HRC. This material withstands constant impacts from sharp sand particles and pebbles, reducing replacement cycles by up to 40% compared to standard pumps.
Heavy-Duty Mechanical Seal with Oil Bath – A double silicon-carbide mechanical seal sits in an independent oil chamber. Even when running partially dry or ingesting small debris, the seal prevents water ingress. This design is crucial for Marine Hydraulic Pump for Sand and Sediment Removal operating in turbid coastal waters.
Hydraulic Motor Direct Drive – No gearbox or coupling means fewer failure points. The axial piston hydraulic motor connects directly to the impeller shaft, delivering instant torque from the carrier excavator. This setup allows variable speed control without electrical hazards underwater.
Vertical Submersible Configuration – As a true Vertical Hydraulic Pump for Offshore Underwater Operation, the motor stays above the waterline while the pump end submerges. This arrangement eliminates the need for long suction hoses and prevents cavitation, even when dredging at 20-meter depths.
Modular Mounting Bracket – The pump attaches to any excavator arm via a customizable steel bracket. Hydraulic hoses connect to the machine’s auxiliary circuit in minutes. No external power source or separate hydraulic power unit is required.
These features directly translate to lower downtime and higher daily tonnage. Operators report continuous runs of 800+ hours before any wear part replacement.
Hydroman® 100THY37-6P Hydraulic Pump for Sea-Marine Work Parameters
| Hydraulic Pump Specification | Hydraulic Motor Specification | |||||||
| Model | Outlet (mm) | Capacity (m³/h) | Head (m) | Power (KW) | Solids handling (mm) | Displacement (ml/r) | Pressure (Mpa) | Oil capacity (L/min) |
| 100THY37-6P | 100 | 160 | 30 | 37 | 55 | 107 | 21 | 107 |
Port Deepening and Coastal Restoration
Shallow harbors and silted river mouths cripple shipping schedules. The Hydroman 100THY Hydraulic Pump for Marine Dredging mounts on a long-reach excavator barge. The operator lowers the pump directly into the sediment layer. Because the pump operates vertically, it sucks material from a concentrated area without stirring excess turbidity.
One project in Rotterdam used three units to remove 1,200 cubic meters of fine sand per day, restoring a 6-meter draft channel in just 11 days. The pump’s wear resistance kept impeller gaps tight, maintaining suction efficiency throughout the contract.
Offshore Aggregate Mining for Construction
Sand and gravel from the seabed form the backbone of concrete and land reclamation. Traditional cutter suction dredgers are expensive to mobilize. The 100THY37-6P Excavator Hydraulic Pump for Sea Work turns any hydraulic excavator into a precision mining tool. Positioned on a jack-up barge, the pump extracts material from underwater deposits at depths up to 15 meters. The 4-inch discharge line moves slurry to a dewatering screen on the barge. A client in the Philippines recovered 350 tons of river sand daily from a submerged alluvial fan. The pump’s 37kW Hydraulic Dredge Pump for Sea Applications rating delivered consistent pressure even when pumping 30% solid content by weight.
Both applications share a common advantage: the pump runs solely on the excavator’s existing hydraulic system. No generators, no long cables, no underwater electrical risks.
Frequently Asked Questions About Vertical Hydraulic Pump for Offshore Underwater Operation
Q1: Can the 4 Inch Hydraulic Submersible Pump for Marine Slurry handle rocks or shells?
Yes, but within limits. The pump passes solids up to 1.2 inches (30mm) in diameter. Sharp shells and small pebbles are fine; larger rocks should be pre-screened or broken. The high-chrome impeller resists chipping, but continuous oversized debris will accelerate wear. For rocky seabeds, consider adding a trash rack or hydraulic grapple to clear boulders first.
Q2: What hydraulic flow and pressure does the excavator need to supply?
The 100THY37-6P Excavator Hydraulic Pump for Sea Work requires 110–150 L/min at 200–250 bar. Most 20–35 ton excavators meet this standard. If your machine is smaller, consult the factory for flow-reducing adapters. Running below minimum flow causes slow impeller speed and potential clogging. Exceeding maximum pressure may damage the hydraulic motor – always install a crossover relief valve.
Q3: How do you maintain this Marine Hydraulic Pump for Sand and Sediment Removal after saltwater use?
Flush the exterior with fresh water at the end of each shift. The internal hydraulic circuit is sealed, but salt crystals can corrode the mounting bracket and fasteners. Every 200 hours, check the oil bath in the mechanical seal housing. If milky, replace the seal. The impeller and wear plate should be inspected every 400 hours; rotate the impeller for even wear or replace when gap exceeds 2mm.
Why This 37kW Hydraulic Dredge Pump for Sea Applications Outperforms Electric Alternatives
Many operators hesitate between hydraulic and electric submersible pumps. Here is the reality for marine work:
Safety – Hydraulic power has zero risk of electric shock, even if the cable gets cut by debris or anchors. Saltwater and high voltage are a deadly combination.
Mobility – No need for a separate generator barge or long power cables. The pump moves with the excavator arm, reaching tight spots under piers and along bulkheads.
Overload Tolerance – An electric pump trips breakers when stalled. A hydraulic pump simply stalls the motor, and the excavator’s relief valve bypasses flow. You reverse the impeller momentarily to clear the jam, then resume.
Compact Footprint – The Vertical Hydraulic Pump for Offshore Underwater Operation sits entirely on the excavator stick. One machine does both digging and pumping, reducing barge space and crew size.
For contractors bidding on coastal dredging projects, the Submersible Hydraulic Pump for Coastal Dredging Projects offers the lowest total cost of ownership. No expensive underwater electrical connectors, no transformer sets, no certified marine electricians.
Hydroman® 100THY37-6P Hydraulic Pump for Sea-Marine Work offers robust 4 Inch Hydraulic Submersible Pump performance. This 37kW vertical Excavator Hydraulic Pump excels in offshore dredging and sediment removal. Contact us today!
Our engineering team provides free hydraulic compatibility checks. Send your excavator model and expected dredging depth – we will confirm fitment within 24 hours. Stock units are available for immediate shipment to major ports worldwide. Custom mounting brackets and hose lengths are fabricated in 7–10 days. Stop losing profits to worn-out electric pumps or expensive dredging subcontractors. Put a Hydroman 100THY Hydraulic Pump for Marine Dredging on your excavator and start moving seabed material efficiently tomorrow.
Related Pumps
Tobee is specialized in providing solutions for slurry pump, vertical sump pumps, gravel pump, dredging pumps, froth pump, seawater pumps, fire pumps, slurry pump parts and OEM pump parts for your harsh projects.
Top Navigation
Top Navigation
Contact Information
+86 180 3203 4573
+86 311 8722 1317
No. 266, Tianshan St, High-tech Zone, Shijiazhuang City 050000, China.
